Cabinets, Enclosures & Containment
The Cable Retractor Arm Kit keeps cables organized and prevents angles, twists and damage.
Cable Lashing Manager creates a simple vertical pathway for multiple cable bundles and has multiple attachment points for securing cables using CPI Saf-T-Grip® Straps or zip ties in N-Series TeraFrame Gen 3 Network Cabinets.
For airflow control and/or equipment mounting, fill empty spaces between mounted equipment.
Ring Cable Manager is independent of the cabinet equipment mounting rails creating a separate vertical pathway for cables and includes plastic cable rings to organize cables. For use with GF-Series GlobalFrame® Gen 2, N-Series TeraFrame® Gen 3 and F-Series TeraFrame® Gen 3 Cabinets.
Set of plastic grommets that cover cable openings in the equipment mounting rails in the wider cabinets to block airflow around equipment.
5 mm Hex Ball Driver Tool, 12"L (300 mm), Each
Additional brackets used to support Raised Floor Enclosures from access floor support pedestals. Kit includes four brackets.
aLight attaches to the bottom, top or side of the CUBE-iT™ Cabinet and provides 4W of LED light.
When used as the rear door on a cabinet, removes heated air and prevents the build up of heated air inside the cabinet, which can cause equipment to overheat and shut down. Standard Fan Doors use single-speed fans.
Clik-Nut® Hardware Kit can be used anywhere along the rack panel surface when mounting, removing or repositioning IT equipment.
Request Free Sample
The Ring Cable Manager organizes loose patch cords along the sides of the cabinet.
Full Height PDU Bracket supports two vertical PDUs side-by-side and has multiple slots for CPI Saf-T-Grip® Straps or tie wraps to secure cords to the bracket. For use with Z4-Series SeismicFrame® Cabinets.
The ThinLine II Intelligent Fan Kit uses a solid state temperature control to vary fan speed from an ultra quiet low speed to low air temperature through increasingly higher speeds as temperature rises.
Ring Cable Manager is independent of the equipment mounting rails, creating a separate vertical pathway for cables and includes plastic cable rings to organize cables. For use with Z4-Series SeismicFrame® Cabinets.
Standard Wall-Mount Cabinet Cable Lashing Bracket secures multiple cable bundles along the side of the cabinet.
Front-to-Back Horizontal Cable Manager snap on to Enhanced Vertical Cable Manager and adjust to match the depth of the cable managers.
Pressurizes interior of the cabinet, forcing warm air out of open vents
Vertical Exhaust Duct attaches to the top of the GF-Series GlobalFrame® Gen 2 or F-Series TeraFrame® Gen 3 Cabinets to provide a sealed pathway for hot air from the top of the cabinet to an overhead drop ceiling as part of a closed hot air retu
Attaches to the outside edge of equipment mounting rails
Telescoping Cable Manager attaches to the sides of the front and rear equipment mounting rail in the N-Series TeraFrame Gen 3 Network Cabinet providing a front-to-rear or vertical pathway for cables along the side of equipment.
The Air Dam Kit blocks airflow around the top, bottom and sides of the rack-mount space inside the F-Series TeraFrame HD Cabinet.
Caster Kits allow cabinets to be moved quickly and easily. When space is limited, cabinets can be placed against the wall when not in service. Casters allow for easy reconfiguration of space.
Use the Side Skirt with the Bolt-Down Kit (P/N 16279-X01) to cover the space along the side of the F-Series TeraFrame HD Cabinet between the bottom of the cabinet frame and the floor.
Fan Kit provides optional ventilation and cooling for the cabinet.
Corner cushions cover the exposed leading edges of racks for added protection.
Use the Cable Lashing Bar to secure a single network or power cable bundle within the cabinet using Saf-T-Grip® Straps or cable ties.
Foam Insert For Cable Ports; For Filtered Ventilation System; Package of 2
Vertical PDU Mounting Bracket Kit used to attach Vertical PDUs to F-Series TeraFrame Gen 3 Cabinet System or GF-Series Gen 2 Cabinet System
Supports one 3.5 inch (89 mm) wide or two 2.3 inch (58 mm) wide CPI Vertical PDU/Power Strips for cabinets and provides multiple attachment points for fastening power cable bundles with Saf-TGrip Straps or cable ties.
Cable Lashing Bracket creates a simple, separate vertical pathway for a small bundle of cables and has multiple slots for CPI Saf-T-Grip® Straps or tie wraps to secure cables to the bracket. For use with GF-Series GlobalFrame Gen 2 or F-Series Tera
These specially designed shelves are suitable for applications where there is a need to access installed equipment for maintenance, upgrading, cleaning, etc.
The Standard Filter Cabinet Ventilation System is for the retrofitting of M-Series MegaFrame Cabinets with fans already located on the cabinet top.
Securely anchor F-Series TeraFrame HD Cabinets to the floor structure for stability with the Bolt-Down Kit.
Air Dam blocks airflow around the sides and top of the equipment mounting space, so cold air passes through equipment and hot air does not recirculate around equipment in the GF-Series GlobalFrame Gen 2 or F-Series TeraFrame Gen 3 Cabinets.
Standard Wall-mount Cabinet Finger Cable Manager attaches alongside the equipment mounting rails to organize patch cords at each rack-mount space (U).
Side Panel With Grommet Sealed Cable Openings feature multiple grommet sealed cable openings that allow cables to enter the side of the cabinet while containing exhaust air within each cabinet.
The Standard Wall-Mount Cabinet Fan Kit provides additional airflow in the unit.
Provides multiple lashing points for premise cables
The Vertical Cable Manager provides cable management in addition to the Integrated Cable Manager. Available for 72”, 78” and 84” (1830 mm, 1980 mm and 2130 mm) cabinets.
The Fiber Slack Manager Panel provides both fiber slack management and a mounting surface for a small fiber manager. Secured under the outermost mounting units, the panel takes up no mounting space within the cabinet. It attaches to the ca
The Seismic Equipment Bracket prevents back-and-forth, side-to-side and up-and-down movement of shelf-mounted equipment by bracing the equipment's chassis to the cabinet's vertical mounting rails.
The Vertical PDU Mounting Bracket Kit is used to attach vertical rack-mount power distribution units (PDUs) with tool-less mounting hardware to M-Series MegaFrame® Cabinet Systems, and C-Series SlimFrame® Cabinet Systems.
Cable Port Brush Kit is a pair of snap on brush covers that can be used to replace the plastic grommets included with the top, bottom and side panels to form a better seal for cable openings.
The Rear Bracket Cable Manager is used to secure service loops at the back of the cabinet.
Optional cover when rectangular knockout on the rear panel is removed
Attach bracing kit to cabinet top panel in installations where there is a risk of seismic activity.
Full Height Dual PDU Bracket supports two vertical PDUs side-by-side and has multiple slots for CPI Saf-T-Grip® Straps or tie wraps to secure cords to the bracket. Two sizes available. For use with GF-Series GlobalFrame Gen 2 or F-Series TeraFrame<
Patch Panel Auxiliary Mounting Rails allow patch panels to be mounted in a cabinet independent of mounting rail location. Front and rear tapped holes accommodate the installation of panel-mounted equipment in addition to providing rear cable management options.
Snap-In Filler Panels blocks airflow in between equipment by sealing unused rack-mount spaces (U) in the cabinet. Use with the Air Dam Kit and Bottom Panel to separate cold and hot air with the cabinet.
Replacement Kit (2 Fans on 1 Frame); Available in 115 VAC or 230 VAC
Attaches to the rear of the equipment mounting rails
Square-Punched Hardware Kits; Several sizes available; M-6, 10-32, or 12-24; Package of 25
Compatible with Low-Decibel Dual-Fan and Standard Fan kits
Allows you to bay and center two F-Series TeraFrame HD Cabinets over 24 inch wide (610 mm) raised access floor tiles.
Specially designed to support heavy equipment. 2U x 19”W x 26”D (660 mm) sliding shelf, extends 24” (610 mm), adjusts between 20” and 34” (510 mm and 860 mm) mounting depth. Supports up to 300 lb (136.1 kg).
Convenient cabinet labeling provided with a dedicated holder to provide cabinet ID and IP address. Package of 12, Black
The Deluxe Filter Cabinet Ventilation System provides “positive pressure” inside the cabinet, ensuring the highest level of protection from airborne dust particles.
Air Dam blocks airflow around the sides and top of the equipment mounting space in Z4-Series SeismicFrame® Cabinets, so cold air passes through equipment, and hot air does not recirculate around equipment.
Bay Seal Kit is only used with 23.6”W (600 mm) GF-Series GlobalFrame Gen 2 or F-Series TeraFrame Gen 3 Cabinets when the cabinets are bayed to align with 24”W (610 mm) floor tiles. The bay seal kit fills the small gaps left between cabinets
Use fixed shelves to support equipment without rack-mounted brackets such as modems, CPUs, small power supplies and monitors.
Air Dam creates a barrier between the cabinet door and the front of equipment along the top, bottom and sides of the cabinet. When used in combination with Perforated Front and Rear doors, Air Dam helps to channel cool air to the front of equipment and
Replacement doors for CUBE-iT™ Wall-Mount Cabinet
Replacement Fan Kit & Junction Box for 2' x 2' Ceiling Enclosure (13812-001) or add to Ceiling Enclosure for Wiring Blocks (13812-003) and Ceiling Enclosure for Patch Panels (13812-002) to support active components.
Enhanced Vertical Manager allows cables to be organized by rack-mount space, making it easier to trace individual cables during moves, adds and changes.
CPI's Raised Floor Grommets provide a reliable seal around cable bundles. The rectangular grommet features a dual-layer brush with an integrated EPDM membrane for a superior seal.
Bottom Panel seals the bottom of the F-Series TeraFrame Gen 3 Cabinets to contain and control airflow in cabinets that are elevated on casters or leveling feet.
Air Director is an angled panel used at the back of cabinets with Vertical Exhaust Duct top panels to guide hot air towards the top of the cabinet.
Mount your 19"W equipment in a 23"W MegaFrame Cabinet with the 23"-19" Rail Adapter Kit that includes 12 adapters and package hardware.
The Vertical Cable Ring Manager attaches to the side of the cabinet’s equipment mounting rails to create a vertical pathway for cables.
Optional locks provide additional security for all standard ceiling enclosures. Includes two locks and two keys.
Provides a compact solution for storing and accessing components. Installs using eight #12-24 screws (not included).
Safely remove a loaded cabinet from the shock pallet at the installation site with this re-usable, heavy-duty steel unloading ramp.
The Retractable Stabilizer Kit is a floor-level brace that provides anti-tip protection when heavy, slide-mounted equipment is extended in front of the cabinet. When not in use, the stabilizer can be retracted under the cabinet for unimpeded aisle spac
Front-to-Rear Cable Manager attaches to the back of equipment mounting rails creating a front-to-rear pathway between the front and rear mounting rails for cables. For use with GF-Series GlobalFrame Gen 2 or F-Series TeraFrame Gen 3 Cabinets.
This unique telescoping design delivers between 20" and 36" of continuous support for up to 100 pounds of equipment in less than 1 RMU of rack-mount space!
Fits any 19" EIA or 23" rack or cabinet. It can be mounted in various orientations to direct additional illumination where it is most needed.
Low-decibel (31 dB), dual-fan option provides quiet operation while keeping active equipment cool
Front-to-Rear Cable Manger attaches to the back of equipment mounting rails in Z4-Series SeismicFrame® Cabinets creating a front-to-rear pathway between the front and rear mounting rails for cables.
Radius Drop attaches to the top of the N-Series TeraFrame Gen 3 Network Cabinet and provides a smooth curved support where cables exit or enter the cable management space along the sides of the cabinet.
Side Panel With Brush Sealed Cable Openings feature multiple brush sealed cable openings that allow cables to enter the side of the cabinet while containing exhaust air within each cabinet.
Cover unused holes in the frame for hinges and installation brackets to prevent bypass airflow.
Replacement plenum rated foam kits for use with Raised Floor and Ceiling Zone Enclosures
Finger Cable Manager attaches to the equipment mounting rail creating a pathway for cables next to the rail, and includes plastic T-shaped cable guides (fingers) that organize cables by rack-mount space (U). Two depths are available.
Lockable Storage Drawer keeps backup media, software, manuals, laptops, test equipment and extra patch cords in close proximity to where they are typically used within a rack or cabinet.
Kit contains four individual label packs, enough for four racks and four cabinets. Labels are constructed of 1/2' W (10 mm) durable polyester film with adhesive backing.
Attaches to rear panel on CUBE-iT™ Cabinets. Creates a 19" EIA x 2U vertical rack-mount space.
The Bottom Panel covers the bottom of the cabinet and blocks airflow into and out of the base of the cabinet. The two-piece telescoping design fits all cabinet F-Series TeraFrame HD Cabinets.